Monopulse tracking system Patent

Monopulse tracking system with antenna array of three radiators for deriving azimuth and elevation indication

Challenging Pre-Service Students\u27 Teaching Perspectives in an Inquiry-Focused Program

Inquiry teaching based on constructivist learning theory has been an emphasis in pre-service education for over a decade. In general, a developmental teaching perspective supports inquiry-based instruction where teachers view learners as constructors of knowledge and teaching as providing questions, problems, and challenges that form a bridge from the learners\u27 prior knowledge to a new, more sophisticated form of reasoning. Since teaching perspectives influence student learning, teacher effectiveness, and teacher attrition, challenging pre-service teachers to overcome experience-based convictions of a transmission perspective is necessary in teacher education. In this study, we examined the teaching perspectives of secondary, pre-service methods students at the midpoint of an inquiry-focused program. Our findings suggest that, despite being introduced to a variety of teaching perspectives, overcoming preconceptions of good teaching and considering a perspective counter to one\u27s disciplinary major presents a dilemma for pre-service teachers

Estimating Percent Residue Cover Using the Line-Transect Method

Leaving crop residue on the soil surface is one of the easiest and most cost-effective methods of reducing soil erosion. Research in Nebraska and other midwestern states has shown that leaving as little as 20 percent of the soil surface covered with crop residue can reduce soil erosion by one-half of what it would be from residue-free conditions. Greater amounts of residue cover will further reduce erosion. Many Conservation Plans specify crop residue management or residue left on the soil surface as the primary erosion control method. Generally, the amount of cover required after planting ranges from 30 percent to as much as 85 percent. Thus, it is important to accurately determine percent residue cover to verify effective erosion control and compliance with a Conservation Plan. Residue cover cannot be estimated merely by looking across a field. Such estimates, often attempted from the road or edge of the field, grossly overestimate the actual amount of cover. Accurate estimates of residue cover can only be obtained from measurements taken within the field, while looking straight down at the soil and residue. Crop residue management, or leaving residue on the soil surface, is the most cost-effective method of reducing soil erosion available to Nebraska farmers. Accurate measurements of percent residue cover are needed to determine if enough cover is present to adequately reduce erosion and to comply with a Conservation Plan. The line-transect method is one of the easiest and most accurate methods of determining percent residue cover

Theoretical and lidar studies of the density response of the mesospheric sodium layer to gravity wave perturbations

The density response of atmospheric layers to gravity waves is developed in two forms, an exact solution and a perturbation series solution. The degree of nonlinearity in the layer density response is described by the series solution whereas the exact solution gives insight into the nature of the responses. Density perturbation in an atmospheric layer are shown to be substantially greater than the atmospheric density perturbation associated with the propagation of a gravity wave. Because of the density gradients present in atmospheric layers, interesting effects were observed such as a phase reversal in the linear layer response which occurs near the layer peak. Once the layer response is understood, the sodium layer can be used as a tracer of atmospheric wave motions. A two dimensional digital signal processing technique was developed. Both spatial and temporal filtering are utilized to enhance the resolution by decreasing shot noise by more han 10 dB. Many of the features associated with a layer density response to gravity waves were observed in high resolution density profiles of the mesospheric sodium layer. These include nonlinearities as well as the phase reversal in the linear layer response

Evidence for multiple structural genes for the γ chain of human fetal hemoglobin

A sequence with a specific residue at each position was proposed for the γ chain of human fetal hemoglobin by Schroeder et al. (1) after a study in which hemoglobin from a number of individual infants was used. We have now examined in part the fetal hemoglobin components of 17 additional infants and have observed that position 136 of the γ chain may be occupied not only by a glycyl residue, as previously reported, but also by an alanyl residue

Speciation in the baboon and its relation to gamma-chain heterogeneity and to the response to induction of HbF by 5-azacytidine

In the baboon (Papio species), the two nonallelic gamma-genes produce gamma-chains that differ at a minimum at residue 75, where isoleucine (I gamma-chain) or valine (V gamma) may be present. This situation obtains in baboons that are sometimes designated as Papio anubis, Papio hamadryas, and Papio papio. However, in Papio cynocephalus, although the I gamma-chains are identical with those in the above mentioned types, the V gamma-chains have the substitutions ala----gly at residue 9 and ala----val at residue 23. The V gamma-chains of P. cynocephalus are called V gamma C to distinguish them from the V gamma A-chains of P. anubis, etc. A single cynocephalus animal has been found to have only normal I gamma-chains and I gamma C-chains (that is, glycine in residue 9, valine in 23, and isoleucine in 75). When HbF is produced in response to stress with 5-azacytidine, P. anubis baboons respond with greater production than do P. cynocephalus, and hybrids fall between. Minimal data on P. hamadryas and P. papio suggest an even lower response than P. cynocephalus. As HbF increases under stress, the ratio of I gamma to V gamma-chains changes from the value in the adult or juvenile baboon toward the ratio in the newborn baboon. However, it does not attain the newborn value. The V gamma A and V gamma C-genes respond differently to stress. In hybrids, the production of V gamma A- chains exceeds that of V gamma C-chains. A controlling factor in cis apparently is present and may be responsible for the species-related extent of total HbF production. It may be concluded that the more primitive the cell in the erythroid maturation series that has been subjected to 5-azacytidine, the more active is the I gamma-gene

Far-ultraviolet Emission-line Morphologies of the Supernova Remnant G65.3+5.7

We present the first far-ultraviolet (FUV) emission-line morphologies of the whole region of the supernova remnant (SNR) G65.3+5.7 using the FIMS/SPEAR data. The morphologies of the C IV {\lambda}{\lambda}1548, 1551, He II {\lambda}1640, and O III] {\lambda}{\lambda}1661, 1666 lines appear to be closely related to the optical and/or soft X-ray images obtained in previous studies. Dramatic differences between the C IV morphology and the optical [O III] {\lambda}5007 image provide clues to a large resonant-scattering region and a foreground dust cloud. The FUV morphologies also reveal the overall distribution of various shocks in different evolutionary phases and an evolutionary asymmetry between the east and the southwest sides in terms of Galactic coordinates, possibly due to a Galactic density gradient in the global scale. The relative X-ray luminosity of G65.3+5.7 to C IV luminosity is considerably lower than those of the Cygnus Loop and the Vela SNRs. This implies that G65.3+5.7 has almost evolved into the radiative stage in the global sense and supports the previous proposal that G65.3+5.7 has lost its bright X-ray shell and become a member of mixed-morphology SNRs as it has evolved beyond the adiabatic stage.Comment: 6 pages, 3 figures, accepted for publication in The Ap

Operating manual for the RRL 8 channel data logger

A data collection device which takes measurements from external sensors at user specified time intervals is described. Three sensor ports are dedicated to temperature, air pressure, and dew point. Five general purpose sensor ports are provided. The user specifies when the measurements are recorded as well as when the information is read or stored in a minicomputer or a paper tape